SURECOM SA-160 LCD Display 0.5-60MHz Color Graphic Antenna Analyzer BNC Connector for Two Way Radio SA160 Antenna Testing Meter
Surecom SA-160 antenna analyzers designed for testing, checking, tuning or repairing antennas and antenna feed lines.
Mainly, these are S.W.R. (Standing Wave Ratio) and impedance measurement instruments (vector impedance analyzers).
Easy-to use measurement modes. make SURECOM attractive for professionals and hobbyists. It is quite important that graphical display of various parameters over a wide frequency range is a key feature of these analyzers which significantly reduces the time required to adjust an antenna.
Main Features:
2.2 ” precision LCD screen,High-lumen LCD brightness, easy to read in direct sunlight
Heavy duty Aluminum enclosure,strong anti-interference ability.
Very compact and convenient for field use
Built-in rechargeable Li-ion battery
Full Band control (No need select Band )
Easy setup, only four control buttons with convenient on-screen soft menus
Constant Battery Status Indicator and Auto Shut-off
Built-in timer shows elapsed time when unit is turned on
High efficiency IC, low power consumption, the longest working hours
More choice measurement frequency Span .
One botton quick scan mode HF1,HF2,HF3 or 3 band by full screen.
Auto marker the Best s.w.r. level reference
Specifications:
Model No. SA-160
Frequency Range: 0.5-60MHz
Connector: BNC (50 OHM)
RF Output Power: 1-1.5V(5 – 10dB)
Frequency Step: 0.1/1/10/100/1000KHz
V.S.W.R. Range: 1.00-19.99
ZRX Range: 0-99.9
Build-in Battery : 3.7V 900mah ,Li-ion 14500
Voltage input : DC5V> 500mA
Frequency stability: <0.5PPM
Span width: 0.54MHz/1.35MHz/2.7MHz/13.5MHz/27MHz/62.1
Charger indicator: Two-color LED Hidden (when not charging) there are three instructions state:
1, charging (red) ;
2, charging is completed (green)
3, Battery fault (flashing)
Charger Plug: Standard Micro USB connector
Size: 70 x 120 x 25 mm
Colour Display: TFT LCD 320 x 240 pixels
Weight: 172g
Power Management
Power Source: Size 14500 of Lithium battery.
Charge Controller: Smart charger, LED charging-status indicator
Voltage Monitor: On-screen DVM, plus battery condition icon
Power Savers: Auto-off timer, Auto Run/Stop RFgenerator control
Interface
RF Connector: BNC -female
Charge Connector: Micro-USB
Control and Display
SPAN: 0.27/0.54/1.35/2.7/5.4/13.5/27/62.1MHz
LCD: 2.2 inch high-output color TFT
Function Keys : 4 botton, with on-screen (soft-menu) identifiers
Tuning: Rotary encoder with press-in tuning-step selection
Weight and Dimensions
Case: Aluminum metal
Size: 7 cm wide x12cm height H x 2.5 cm
Weight: 6.1 oz (0.172 kg)
Turn on and off the power
Turn on the power, Press and hold White botton when the dot disappear
from left up angle ,. top Menu appeared on the screen.
Turn off the power, You have 2 method :
a)On Top Menu page ,Press and hold the White [F1 ] botton at 5 second .
b)On Top Menu page , Rotary encoder on “Power off”, Press the [F2 Enter]
1.1Function Select
You can turn the knob select you want function and press [F2.Enter] botton .
2.0 ANTENNA TEST EXAMPLES by Scan mode
2.1[Scan] mode page
In the Top Menu screen: Rotary encoder on “Scan”, Press the [F2 Enter], to frequency mode measurement button, enter Scan (scan mode) screen.
Press [F.2 scan ],button to start the scan operation. During scanning, in order to ensure measurement accuracy, each frequency will stay for short while. one scanning cycle will take about 1-2 seconds. Once SCAN is done, it will enter ”Present” mode (result) screen
You have results on the screen : Show the SWR curve only (because default setting SWR curve only , Zx curve, Rs curve Disable) You can Enable other curve on the screen: On Top Menu page,
Rotary encoder on “Zx”, Press the [F2 Enter] to enable . Other cure will Disable when Power Off , If want enable in the future, Rotary encoder on “Save”, Press the [F2 Enter] to save setting .
2.2 1. lnfull (default SCAN range 0.56MHz -59.9MHz,span 62.1MHz )
* Long press to [SCAN ]and press [F3 UPDn] select “1.Infull”,and then release the scan botton.
2.lrnMk=(Learn marker move to center frequency)
* Long press to [SCAN ]and press [F3 UPDn] select “2.IrnMk”,and then release the scan botton.
2.3 [View]
view the scan frequency point on the curve on each scan of the specific parameters of the measurement results.
– Press the [F3.View ] button to start the view operation mode. rotary encoder ,the white triangle curve marker is move
– Dot scale will display on screen, Press bottom change the Dot scale,You have 3 options of Dot scale mode for choose,[Dot =x1] [Dot=x10][Dot= x25] . (230KHz,2.3MHz,5.8MHz)
SWR Full scale will display on screen,Press bottom change the graphically plot SWR,You have 3 options scale mode for choose, [SWR=x2 ][SWR= x 0.5][SWR=x1] .(1-9,1-19,1-4.5)
2.4[ Quick 1] start Scan mode:
Quick view the scan frequency point on the curve on each scan
Press the button [Quick 1 ] to start the Quick 1 operation mode .You have 3 options scan mode for choose .
1)Press the button [F1. Scan 1 ] 0.5 to 27.3MHz can of the specific parameters of the measurement results.
2)Press the button [F2. Scan 2 ] 16.6 to 43.4MHz can of the specific parameters of the measurement results.
3)Press the button[F3. Scan 3 ] 33.6 to 60.0MHz can of the specific parameters of the measurement results.
PACKAGE CONTAIN:
1 x SURECOM SA160 (ENGLISH VERSION) Colour Graphic Antenna Analyzer
1 x English User”s Manual
1 x Mirco Usb Charger Cable
Reviews
There are no reviews yet.